Microsoft LPF-00004 Návod k obsluze Strana 102
- Strana / 157
- Tabulka s obsahem
- ŘEŠENÍ PROBLÉMŮ
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Page 84 CyberControl SOFTWARE
C
YBER
A
MP
380, COPYRIGHT MARCH 2002, AXON INSTRUMENTS, INC.
Starting CyberControl
When CyberControl is opened, the application automatically starts communications through the serial
port. This is the Initialization portion of the startup sequence. If the CyberAmp is not powered up, or is
not attached to the correct port, the application will ask if it should enter a demonstration mode, a
feature designed to show the operation of the application when a CyberAmp is not attached.
Alternatively, one can choose the CyberControl Preferences panel to change the Serial Communication
Rate or the Serial Port. The Status Scanning Rate, the rate at which the CyberAmp status is interrogated
and used to update the spreadsheet, can also be set in this display. As the scanning may take computer
overhead or generate beat noise, it can also be disabled by choosing Scanning Disabled.
In the second portion of the initialization sequence, the application checks for any CyberAmps attached
to the computer. The progress graph continues all the way to the right of the window. When the
scanning is finished, a new window will be opened that represents the attached CyberAmp.
The CyberAmp Window
PC: Each CyberAmp channel is displayed individually via a tabbed interface.
Macintosh: A spreadsheet is used to show the status of all channels of the attached CyberAmp
amplifier, and consists of one row for each channel. The CyberAmp window also has a
gray bar that contains the CyberAmp icon. Clicking on the CyberAmp icon will reduce the
window to an icon; clicking on it again will restore the window. And, when any channel on
the CyberAmp amplifier is overloaded, the icon is inverted and turns red.
Figure 31. The CyberControl window on a PC.
1) CHANNEL NUMBER COLUMN
PC: Separate tabs display each channel number. Click on a channel number to see its
individual settings.
Macintosh: The first column displays the channel number; clicking on a channel row in this
column selects the entire row, andthe contents of the entire row can be copied and
pasted to another channel. Clicking in this column in the row of the title bar selects
- CyberAmp 380 1
- Declaration of Conformity 3
- IMPORTANT INFORMATION 5
- RENSEIGNMENTS IMPORTANTS 6
- WICHTIGE INFORMATIONEN 7
- INFORMACION IMPORTANTE 8
- Explanation of symbols 9
- Explication des symboles 9
- Explicación de símbolos 9
- SÉCURITÉ 10
- SICHERHEITS 10
- HINWEISE 10
- SEGURIDAD 10
- COPYRIGHT 11
- VERIFICATION 11
- TABLE OF CONTENTS 13
- INTRODUCTION 19
- Page 2 INTRODUCTION 20
- INTRODUCTION Page 3 21
- FUNCTIONAL DESCRIPTION 23
- General Features 26
- FUNCTIONAL CHECKOUT 29
- TYPICAL CONFIGURATIONS 33
- Supply Voltage 37
- Changing the Fuse 37
- Grounding and Hum 38
- Power-Supply Glitches 39
- Input Coupling 39
- Expansion 40
- Low-Pass Filter 41
- Amplitude Characteristics 42
- Sampling Rate 43
- 10-90% Rise Time 43
- AC Coupling and Autozeroing 44
- 3 dB frequency of 44
- Time Constant 46
- 100 1.6 46
- Saturation 47
- Notch Filter 48
- Overload Detection 49
- Audio Monitor 50
- External Input 51
- Electrode Test 52
- Strain Gauges 55
- Active Probes 56
- Common-Mode Rejection Ratio 57
- Troubleshooting 59
- TRANSDUCERS 61
- Page 44 TRANSDUCERS 62
- TRANSDUCERS Page 45 63
- EMG, EEG, ECG Recording 64
- Nerve Cuffs 65
- Metal Microelectrodes 65
- Page 48 TRANSDUCERS 66
- Pressure 67
- Acceleration 67
- Self Heating 68
- Isolation 68
- Insulation Techniques 68
- AI 400 SERIES SmartProbes 69
- Transducer Adapter 71
- Input Connector Color Scheme 72
- Recommended Input Coupling 73
- Connector 74
- Example Circuits 75
- Basic Thermistor Circuit 76
- Amplifier Probes 78
- Current Probes 79
- Photodiode Amplifier 79
- Linear Potentiometers 80
- Rotary Potentiometers 80
- Panel Switch 81
- Foot Switch 81
- CMD300 CONTROL SOFTWARE 83
- Command-Line Mode 85
- Interactive Mode 85
- Command-File Mode 86
- Command Reference 87
- CMD300 OVERLOAD 91
- CMD300 REPEAT OVERLOAD 94
- QUICK300 CONTROL SOFTWARE 97
- Command Line Options 100
- CyberControl SOFTWARE 101
- Starting CyberControl 102
- Overload Handling 105
- Keyboard Commands 105
- Communications Settings 107
- PC Menus 108
- Macintosh Menus 109
- PROGRAMMER'S GUIDE 112
- Libraries and Example Code 114
- > end of response 116
- AT3F5 24000 118
- 2 4 6 8 10 ... 28000 30000 118
- AT8R06000 121
- D5=-1234500 124
- Implementation Notes 125
- Support Routine Details 125
- Example Programs 129
- SPECIFICATIONS 135
- Page 118 SPECIFICATIONS 136
- Offset range: ±10 V 137
- Page 120 SPECIFICATIONS 138
- SPECIFICATIONS Page 121 139
- Page 122 SPECIFICATIONS 140
- REFERENCES 141
- ADJUSTMENT PROCEDURES 143
- Other Adjustments 144
- CIRCUIT DIAGRAMS Page 127 145
- SERIAL COMMUNICATIONS CABLES 147
- LIST OF FIGURES AND TABLES 149
- WARRANTY 151
- WARNING 153
- INDEX Page 137 155
Související produkty a manuály pro Měření, testování a kontrola Microsoft LPF-00004
(82 stránky)© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.062 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce